Hey everybody, Ryan here at etrailer. Today on our 2020 Lincoln Corsair, we're going to be taking a look at and showing you how to install the Tecontra upgraded vehicle wiring harness with a four way flat trailer connector. So the way this kit is going to work is it's going to provide you with the necessary lighting functions to eliminate all of the lights on your trailer. So whenever you're ready to use it, you can open up your hatch, lift up your floor covering, and it's going to be located right here inside. Now you can always run it outside and mount it up next to your hitch if that's what you want to do, but for the most part, I think this is a safe bet. So you have your four-way flat, and you're just going to close this in the hatch. more
6/2/2021 9:59:36 AM
Trailer Wiring Harness Installation - 2012 Lincoln MKZ- Video
Today on our 2012 Lincoln MKZ, we'll be installing the Tow Ready Custom Fit Vehicle Wiring Harness, part number 119179KIT. To begin our install, we'll first need to access the wiring behind the taillight assemblies. To do this, we'll start by removing the rear cargo liner and spare tire cover. Then we'll need to remove the rear threshold. There are six fasteners that we'll need to remove. These are push pin fasteners, so we'll gently pry out on the fastener until it releases. Once we have all six fasteners removed, we'll gently pull up on the rear threshold until the fasteners underneath release. more
10/29/2014 4:25:54 PM
Trailer Wiring Harness Installation - 1996 Lincoln Mark VIII- Video
Today on our 1996 Lincoln Mark VIII, we'll installing the Tow Ready 4-Pole Wiring Harness, Hardwire kit, part number 119179KIT. To begin our install, we'll first open up the trunk. We'll need to access the manufacturer's wiring here on the driver's side so to do that, we'll remove the cargo hook here that also secures the carpeting. We can set it aside, pull back the carpeting and expose the manufacturer's wire. Next, we'll need to locate the turn and brake signal for each side along with the running light circuit. To do that, we're going to go ahead and remove some of the electrical tape here on the manufacturer's harness and then use the test light to locate the correct wiring. more
9/5/2014 10:19:37 AM
Trailer Wiring Harness Installation - 2009 Lincoln Town Car- Video
Today on our 2009 Lincoln Town-car, we'll be installing the Tow Ready Four Pole Wiring Harness, part number 119179KIT. To install the new harness, we'll open up the rear trunk and then remove the interior paneling so we can gain access to the Manufacturer's wiring. We'll first need to remove some pushpin fasteners and then remove the rear threshold. We'll remove the fasteners that secure the carpeting behind the taillight assembly on the driver's side. Now that we have access to the taillight wiring, we'll go ahead and take a test light and test the wiring to verify the signal wire. We'll need to locate the left and right turn signal, running light circuit and brake light circuit so that we can use the quick splice connectors to secure our new Tow Ready Harness directly to the manufacturer's wiring. For the passenger side turn signals, it's going to be an orange wire with a blue stripe. Next we'll take our quick splice connector, slide over the manufacturer's wire, then take the green wire from our harness, slide it into the connector, and crimp it down. For our left turn signal, left braking, it's going to be the green wire with an orange stripe. more
7/30/2014 2:57:53 PM
Trailer Wiring Harness Installation - 2006 Lincoln Town Car- Video
Today on our 2006 Lincoln Town Car, we'll be installing the Curt upgraded circuit protected tail light with converter hardwire kit with a 4-pole end and it includes a tester. Part number 56146kit.Now to begin with, we'll go ahead and open up the rear trunk of the vehicle. To remove the rear threshold we'll need to remove four push fasteners, two on each side up high and two in the center.Once we have all four of these fasteners removed, we can go ahead and pop the rear threshold out. Either a large flathead screwdriver or a trim panel removal tool works well for doing this.Next we'll go ahead and remove the trunk lining. We'll also have to take off the cover that covers up the spare tire. There's another nut cover that you'll need to remove. more
12/16/2013 10:50:30 PM
Trailer Wiring Harness Installation - 2002 Lincoln Continental- Video
Today on this 2002 Lincoln Continental, we are going to install part number 119176 from Tow Ready. We are also going to use part number 118151. We will start off by opening the trunk because all of our connections will be on the inside. The first thing we need to do is go ahead and remove the threshold right here. And then we can pull back our carpeting and have access to the wiring. It looks like there are a couple of rivets right here. OK, go ahead and remove one more rivet down here. Remove this rivet up here. You can see here we have access to our wire harness right here and also a factory ground screw. The first thing we are going to do is take our wire harness apart and figure out which wire has which function. Remove it from the side here. 1:02 more
12/16/2010 7:09:35 AM
Filter Videos
Filter Videos
